Maverick Wolfe
Solid State Member
- Messages
- 13
- Location
- Kitsap County, WA
I Said in my intro thread I would be posting this up. Well, Here goes the list of parts for my planned build.
Case:HAF 932--Currently in use
Koolance parts for planned build inside and outside this case:
CPU 380A Block
1x 3x120MM 53mmThick Radiator 2x 120mmx38mm ~200CFM Fans
1x 3x140mm Standard Radiator
2x Dual Bay Res for pmp 450S
1x 450S pump
1x 3x120mm Shroud
1x 3x120mm enclosure/riser
1x shroud mounting kit
1x3x140MM shroud
2x 38mm screw kits for 120MM fans
1x Fillport
1x Round 80mmX80MM "Feeder" Res for additional capacity of liquid.
10x 1/2" 13mm Black Barb Fittings
I'm considering attempting to put a Peltier onto a smaller radiator outside the loop with some sort of crazy mod, or even a peltier Chilled Metal Water box outside the system, but I'd have to have it custom made by koolance. I'm leaning towards a Water box/peltier system instead of the elaborate 3 res solution. there would be at least 2 Peltiers within the waterbox system I'm just tossing around concepts in my head right now. not sure if I'm going to even use a peltier.
Layout of primary cooling system:
3x120 with Riser and shroud, on top of case, with fans installed into the shroud as per instructions and necessary modifications will be made to the installation procedure as to optimize height due to 3x140mm Radiator running from the rear, Radiator will be setup in such a way that It will be upside down due to the barbs needing to be facing up. 2x pmp 450's may be needed instead of one because of this. I would run them both at the exact same speed. so as to pull double the flow through my system. I might change the 3x140 to a 2x140 instead because of the size in height.
This system will be Chilling at the very least 1xFX8350 CPU to start. My Intended Flow Chart:
Res<<Pump>>CPU>>3x120mm>>2/3x140mm>>Res
Eventually it will go:
Res<<Pump>>CPU>>3x120mm>>Vid>>2/3x140mm>>Ram>>1x120mm>>Res
I'll probably Nix the crazy TEC Idea as it's just that... Crazy.... Ideas on my loop? I will also be Swapping out my Stock 230MM side Fans for a Bitfenix Pro 230MM fans.
Case:HAF 932--Currently in use
Koolance parts for planned build inside and outside this case:
CPU 380A Block
1x 3x120MM 53mmThick Radiator 2x 120mmx38mm ~200CFM Fans
1x 3x140mm Standard Radiator
2x Dual Bay Res for pmp 450S
1x 450S pump
1x 3x120mm Shroud
1x 3x120mm enclosure/riser
1x shroud mounting kit
1x3x140MM shroud
2x 38mm screw kits for 120MM fans
1x Fillport
1x Round 80mmX80MM "Feeder" Res for additional capacity of liquid.
10x 1/2" 13mm Black Barb Fittings
I'm considering attempting to put a Peltier onto a smaller radiator outside the loop with some sort of crazy mod, or even a peltier Chilled Metal Water box outside the system, but I'd have to have it custom made by koolance. I'm leaning towards a Water box/peltier system instead of the elaborate 3 res solution. there would be at least 2 Peltiers within the waterbox system I'm just tossing around concepts in my head right now. not sure if I'm going to even use a peltier.
Layout of primary cooling system:
3x120 with Riser and shroud, on top of case, with fans installed into the shroud as per instructions and necessary modifications will be made to the installation procedure as to optimize height due to 3x140mm Radiator running from the rear, Radiator will be setup in such a way that It will be upside down due to the barbs needing to be facing up. 2x pmp 450's may be needed instead of one because of this. I would run them both at the exact same speed. so as to pull double the flow through my system. I might change the 3x140 to a 2x140 instead because of the size in height.
This system will be Chilling at the very least 1xFX8350 CPU to start. My Intended Flow Chart:
Res<<Pump>>CPU>>3x120mm>>2/3x140mm>>Res
Eventually it will go:
Res<<Pump>>CPU>>3x120mm>>Vid>>2/3x140mm>>Ram>>1x120mm>>Res
I'll probably Nix the crazy TEC Idea as it's just that... Crazy.... Ideas on my loop? I will also be Swapping out my Stock 230MM side Fans for a Bitfenix Pro 230MM fans.