Job well done :)

gurusan · 06-13-2008, 03:07 PM

Finally lapped my E6750...I normally lap all my cpus but was too lazy to do
this one, but finally got around to it..and now she looks purdy!

Preacher · 06-13-2008, 03:24 PM

Very pretty , temp drops ?

gurusan · 06-13-2008, 03:27 PM

hard to gauge temp drops since I switched from air cooling to watercooling at the same time.

33c idle @ 3.64ghz 1.36V
46c full load

i did a retarded thing though and only ordered a single 1/2" barb instead of two. I was slightly drunk at the time and I guess I assumed they were sold in pairs. So I'm running a 1/2" inlet and 3/8" outlet on my block, pretty sure that's hurting my delta T. Also I cleaned my ancient radiator out with vinegar today and all sorts of sludge came out...shined a light in and it looks a bit better but there's still a bit of corrosion and limescale. A new 120.3 is next on my list. This radiator is really showing its age.

Drizzt5 · 06-13-2008, 03:42 PM

Nice lapping, I'm still scared to lap mine

.

06-13-2008, 03:07 PM	#1 (permalink)
gurusan Moderator Join Date: Jan 2006 Location: Oxford, UK Posts: 5,604	Job well done :) Finally lapped my E6750...I normally lap all my cpus but was too lazy to do this one, but finally got around to it..and now she looks purdy! __________________ :: Antec P182 :: Asus P5Q Deluxe :: Intel E8500 @ 4511MHz :: :: Thermaltake Toughpower 750w :: HD4850 512mb 880/1150 :: :: 4gb OCZ @ 1187mHz 5,5,5,15 :: 120.3+D4+XSPC Edge+Maze4 ::

06-13-2008, 03:24 PM	#2 (permalink)
Preacher Master Techie Join Date: Aug 2006 Location: Ra'anana, Israel Posts: 2,279	Re: Job well done :) Very pretty , temp drops ? __________________

06-13-2008, 03:27 PM	#3 (permalink)
gurusan Moderator Join Date: Jan 2006 Location: Oxford, UK Posts: 5,604	Re: Job well done :) hard to gauge temp drops since I switched from air cooling to watercooling at the same time. 33c idle @ 3.64ghz 1.36V 46c full load i did a retarded thing though and only ordered a single 1/2" barb instead of two. I was slightly drunk at the time and I guess I assumed they were sold in pairs. So I'm running a 1/2" inlet and 3/8" outlet on my block, pretty sure that's hurting my delta T. Also I cleaned my ancient radiator out with vinegar today and all sorts of sludge came out...shined a light in and it looks a bit better but there's still a bit of corrosion and limescale. A new 120.3 is next on my list. This radiator is really showing its age. __________________ :: Antec P182 :: Asus P5Q Deluxe :: Intel E8500 @ 4511MHz :: :: Thermaltake Toughpower 750w :: HD4850 512mb 880/1150 :: :: 4gb OCZ @ 1187mHz 5,5,5,15 :: 120.3+D4+XSPC Edge+Maze4 :: Last edited by gurusan; 06-13-2008 at 03:30 PM.

06-13-2008, 03:42 PM	#4 (permalink)
Drizzt5 Banned Join Date: Oct 2007 Location: New Joisy Posts: 2,815	Re: Job well done :) Nice lapping, I'm still scared to lap mine .

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New job.	SiZcO	Off Topic Discussion	13	04-12-2008 06:49 PM
Sweet new job (finally!)	jorsoft03	Off Topic Discussion	10	01-05-2008 08:23 PM
Job prospects	beedubaya	Discussion on Computer Jobs, Degrees, Certifications	11	10-17-2007 07:04 PM