HEre's the #'s. What next?

Indobos · 07-25-2007, 03:27 PM

Okay so I ran the system for 5 hours. Full load on Orthos. Mobo @ 38C, cpu @ 42c, Core 1 @ 51C, core 2 @ 52C. 350mhz, Vcore @1.3525. Should I try to run up the bus or should I kick in some more volts. Then attempt to increase bus? or am I getting the temps too high?

Nagasama · 07-25-2007, 06:55 PM

temps are just fine.
i'd see how far i could go with that voltage, and go up if need be.
with those temps you have quite a bit of headroom.

Indobos · 07-25-2007, 07:06 PM

Quote:

Originally Posted by nagasama

temps are just fine.
i'd see how far i could go with that voltage, and go up if need be.
with those temps you have quite a bit of headroom.

What would you say is the most temps I want to see at full load? So if I increase the bus speed and wont boot or is unstable start to ramp up the power?

MetalOwns · 07-25-2007, 08:07 PM

Quote:

Originally Posted by Indobos

What would you say is the most temps I want to see at full load? So if I increase the bus speed and wont boot or is unstable start to ramp up the power?

Lower the speed then test for stability. Then if you want to go faster, then give it more juice. Temps are good, but how are your core temps so much higher than your CPU temp? My CPU, Core 1, and core 2 temps are almost the same.

What processor is that?

EDIT: nevermind about the processor...I just saw it in your sig. Your computer is similar to mine by the way.

b1gapl · 07-25-2007, 09:56 PM

The most you would want to see, is 60-65C on load. If Orthos is running fine at 350, at 1.3525v, go to 375 and test Orthos again. If it's not able to post or it's unstable, during Orthos....bump up the voltage one more notch, and re-test again.

Indobos · 07-26-2007, 02:46 AM

okay so I bumped up the voltage to 1.3625 @375 mhz and no boot. just would post then would blue screen adn dump. so i upped the voltage 3 times total to 1.3825 @ 375mhz and still no boot to windows. I dropped the voltage back to 1.3625 and 365mhz. and am going to run orthos for the night. why san I not get to 375mhz? Do I need to kick up the voltage that much to get 375mhz to work? what is the max voltage to give to the CPU? I don't want to fry anything. **** orthos stopped as I was writing this. gonna kick up the voltage again see what happens. please post any opinions.

Nagasama · 07-26-2007, 09:40 AM

how is your ram set up(speed, voltage, divider, etc)? that would be a (very) likely cause for it not booting even though you are upping the voltage of your cpu. your ram may be maxed out.

b1gapl · 07-26-2007, 09:45 AM

I think it would be better, if he had a 1:1 FSB and RAM ratio, correct? That's what I always try to do. Although now, I'm at a 4:5..

Nagasama · 07-26-2007, 09:51 AM

indeed that would keep his ram under stock(till fsb of 400 obviously), and probably give the cpu more headroom.
i can almost guarantee that his ram is overclocked too much.

Indobos · 07-26-2007, 10:00 AM

What info on the ram do you need? how can I tell its being overclocked? what do I need to change?

07-25-2007, 03:27 PM	#1 (permalink)
Indobos Super Techie Join Date: Jun 2007 Posts: 287	HEre's the #'s. What next? Okay so I ran the system for 5 hours. Full load on Orthos. Mobo @ 38C, cpu @ 42c, Core 1 @ 51C, core 2 @ 52C. 350mhz, Vcore @1.3525. Should I try to run up the bus or should I kick in some more volts. Then attempt to increase bus? or am I getting the temps too high? __________________ Mobo: GA-p35-DS3r CPU: Q6600 @ 2.4Ghz G0 Video: EVGA 8800 GTS 512MB (G92) 670/972 for the Acer 24" Monitor P/S: Rosewill RP 550-2 Pro Case: Antec 900 2X HD: SEAGATE 7200.2 320GB Memory: G.SKILL 2 GB PC6400 DDR2 800 Os: Windows Vista Premium 32BIT

07-25-2007, 06:55 PM	#2 (permalink)
Nagasama Master of the Donkeypunch Join Date: Oct 2006 Location: your mom's house Posts: 5,689	Re: HEre's the #'s. What next? temps are just fine. i'd see how far i could go with that voltage, and go up if need be. with those temps you have quite a bit of headroom. __________________ q9450~3.75 very fast ghz~~asus P5Q Deluxe~~2 x 2gb OCZ reaper 1066~ ~Sapphire HD4870 1gb~ * folding rig * AMD x2 3600 @ 2.95ghz : 2gb OCZ ddr2 800 : EVGA 8800gts 512 : Asus M3A78-EM 780g

07-25-2007, 09:56 PM	#5 (permalink)
b1gapl Commander SMod Join Date: Nov 2004 Location: New York City Posts: 11,803	Re: HEre's the #'s. What next? The most you would want to see, is 60-65C on load. If Orthos is running fine at 350, at 1.3525v, go to 375 and test Orthos again. If it's not able to post or it's unstable, during Orthos....bump up the voltage one more notch, and re-test again. __________________ Recommended PC Components Guide Potentially the longest thread in history!! Tech-Forums Official 3DMark06/05/03 Top List

07-26-2007, 02:46 AM	#6 (permalink)
Indobos Super Techie Join Date: Jun 2007 Posts: 287	Re: HEre's the #'s. What next? okay so I bumped up the voltage to 1.3625 @375 mhz and no boot. just would post then would blue screen adn dump. so i upped the voltage 3 times total to 1.3825 @ 375mhz and still no boot to windows. I dropped the voltage back to 1.3625 and 365mhz. and am going to run orthos for the night. why san I not get to 375mhz? Do I need to kick up the voltage that much to get 375mhz to work? what is the max voltage to give to the CPU? I don't want to fry anything. **** orthos stopped as I was writing this. gonna kick up the voltage again see what happens. please post any opinions. __________________ Mobo: GA-p35-DS3r CPU: Q6600 @ 2.4Ghz G0 Video: EVGA 8800 GTS 512MB (G92) 670/972 for the Acer 24" Monitor P/S: Rosewill RP 550-2 Pro Case: Antec 900 2X HD: SEAGATE 7200.2 320GB Memory: G.SKILL 2 GB PC6400 DDR2 800 Os: Windows Vista Premium 32BIT

07-26-2007, 09:40 AM	#7 (permalink)
Nagasama Master of the Donkeypunch Join Date: Oct 2006 Location: your mom's house Posts: 5,689	Re: HEre's the #'s. What next? how is your ram set up(speed, voltage, divider, etc)? that would be a (very) likely cause for it not booting even though you are upping the voltage of your cpu. your ram may be maxed out. __________________ q9450~3.75 very fast ghz~~asus P5Q Deluxe~~2 x 2gb OCZ reaper 1066~ ~Sapphire HD4870 1gb~ * folding rig * AMD x2 3600 @ 2.95ghz : 2gb OCZ ddr2 800 : EVGA 8800gts 512 : Asus M3A78-EM 780g

07-26-2007, 09:45 AM	#8 (permalink)
b1gapl Commander SMod Join Date: Nov 2004 Location: New York City Posts: 11,803	Re: HEre's the #'s. What next? I think it would be better, if he had a 1:1 FSB and RAM ratio, correct? That's what I always try to do. Although now, I'm at a 4:5.. __________________ Recommended PC Components Guide Potentially the longest thread in history!! Tech-Forums Official 3DMark06/05/03 Top List

07-26-2007, 09:51 AM	#9 (permalink)
Nagasama Master of the Donkeypunch Join Date: Oct 2006 Location: your mom's house Posts: 5,689	Re: HEre's the #'s. What next? indeed that would keep his ram under stock(till fsb of 400 obviously), and probably give the cpu more headroom. i can almost guarantee that his ram is overclocked too much. __________________ q9450~3.75 very fast ghz~~asus P5Q Deluxe~~2 x 2gb OCZ reaper 1066~ ~Sapphire HD4870 1gb~ * folding rig * AMD x2 3600 @ 2.95ghz : 2gb OCZ ddr2 800 : EVGA 8800gts 512 : Asus M3A78-EM 780g

07-26-2007, 10:00 AM	#10 (permalink)
Indobos Super Techie Join Date: Jun 2007 Posts: 287	Re: HEre's the #'s. What next? What info on the ram do you need? how can I tell its being overclocked? what do I need to change? __________________ Mobo: GA-p35-DS3r CPU: Q6600 @ 2.4Ghz G0 Video: EVGA 8800 GTS 512MB (G92) 670/972 for the Acer 24" Monitor P/S: Rosewill RP 550-2 Pro Case: Antec 900 2X HD: SEAGATE 7200.2 320GB Memory: G.SKILL 2 GB PC6400 DDR2 800 Os: Windows Vista Premium 32BIT

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode